DEALER LOGIN

GRIPPING STATIONS

A130631 Shaft and Ferrule Prepping Machine with Flap Wheel

USD $323

This heavy duty prep-ping center roughens shaft tips evenly on both steel & graphite shafts and turns down ferrules on assembled clubs. We've re-powered this design with a motor that has 20% more torque to give clubmakers the ability to cut through and buff heavily soiled clubheads to restore them to like new condition.

A130631-240V Shaft and Ferrule Prepping Machine with Flap Wheel

USD $323

This heavy duty prep-ping center roughens shaft tips evenly on both steel & graphite shafts and turns down ferrules on assembled clubs. We've re-powered this design with a motor that has 20% more torque to give clubmakers the ability to cut through and buff heavily soiled clubheads to restore them to like new condition.

A130645 Compact Shaft Cutter And Ferrule Prepping Center

USD $220

The Golfmechanix Shaft cutter and Ferrule prepping centre is the ideal the small workshop or the occasional clubmaker. Clean, compact and well thought-out; this design has the power to slice through steel and graphite shafts, and turn ferrules down to size. We've re-powered this design with a motor that has 15% more torque, so that heavier belts can be used to cut through deep scratches and buff heavily soiled clubheads to restore them to like new condition.

A130645-240V Compact Shaft Cutter and Ferrule Prepping Center

USD $220

The Golfmechanix Shaft cutter and Ferrule prepping centre is the ideal the small workshop or the occasional clubmaker. Clean, compact and well thought-out; this design has the power to slice through steel and graphite shafts, and turn ferrules down to size. We've re-powered this design with a motor that has 15% more torque, so that heavier belts can be used to cut through deep scratches and buff heavily soiled clubheads to restore them to like new condition.

A130647 Compact Heavy Duty Shaft Preping Center

USD $391

The GolfMechanix Industrial Grade Shaft Prepping Center is an integrated work station designed to handle all of your shaft cutting and prepping needs, as well as turning down and finishing ferrules. The powerful 0.5 Hp 3,400 RPM motor provides ample power and is fitted with our high performance 6 inch cutoff wheel to easily slice through steel and graphite shafts, with very little dust or noise pollution! A graduated ruler ensures cutting accuracy.

A130647-240V Compact Heavy Duty Shaft Preping Center

USD $391

The GolfMechanix Industrial Grade Shaft Prepping Center is an integrated work station designed to handle all of your shaft cutting and prepping needs, as well as turning down and finishing ferrules. The powerful 0.5 Hp 3,400 RPM motor provides ample power and is fitted with our high performance 6" cutoff wheel to easily slice through steel and graphite shafts, with very little dust or noise pollution! A graduated ruler ensures cutting accuracy. 240 Volt.

A130900 Semi Automatic pneumatic ferrule installer

USD $1,757.50

Mounting ferrules on a shaft is neither a fast nor pleasant production step, as it requires a good level of manual dexterity, focus as well as brawn, and could be hazardous to both the shaft and operator when fatigue sets in! We’ve designed this pneumatic ferrule installer for batch processing shafts trimmed to the same length to improve the precision and consistency of this critical production step while making the process safe and effortless.

A190200 Shaft Tip Abrader

USD $25.50

The answer to abrading graphite shaft tips. Just a few turns and the coating is fully removed for a proper shaft bond. Special wound coil stainless steel wire brush and compression nut compensate for wear. One size fits all shaft tips.

A130300 Ferrule Trimmer

USD $22.31

A simple and efficient tool that enables clubmakers to turn down ferrules, flush with the hosel, without the need of a belt sander.

A130500 Ferrule finishing and shaft tip preparation tool

USD $26.35

This unique dual purpose tool is used for finishing ferrules to a high gloss finish as well as prepping shaft tips prior to installation. It uses a synthetc lint free cloth strip soaked with acetone on which the ferrule is spun. Nylon roller bearing support the shaft during the process. The lint free cloth strips can be replaced with 80 grit sand paper to prepare shafts, thin down ferrules etc

A130601 Universal Ferrule Turning Arm

USD $33.25

A ferrule turning arm designed around 42" belt sanders. This design allows the pod to rotate 30 degrees around its base and has up to 4 inches of reach back and forth. This makes for a very comfortable position from wich to thin down ferrules of any size, hosel length or head size. The shaft rest are made of non abrasive engineering nylon. Bolts directly to the bench behind the motor.

A130700 Mr T Universal Ferrule Tool

USD $11.48

A small hand-tool designed for installing ferrules of any size to the correct insertion depth. For use on both wood and iron shafts .

A130721 Ferrule Insertion Setter

USD $25.50

Precision tool for inserting ferrules to the correct depth. Bolts onto a bench. Most designs drive the ferrule into the shaft. The key feature of this design is that it does the opposite - the shaft is driven into the ferrule. This prevents ferrules from being blunted.

A130740 Ferrule Saver Extractor

USD $14.88

Ever pushed a ferrule too far up the shaft? Did you just cut it off and throw it away? This simple and ingenious device allows you to easily return a "runaway" ferrule to the desired location (or extract it) without damaging it or the shaft..

A130800 Ferrule Slicer & Splitter

USD $21.04

A small hand-tool designed for slicing and splitting ferrules prior to shaft extraction.

A210230 Ferrule Extraction Spacer kit

USD $14

This is an essential re-shafting tool for Callaway and Ping clubheads. The ferrule shield protects and cools the proprietary ferrule while the head is being heated. The ferrule shield also provides a shoulder on which to push against. Click options for spacer only.

A260501 Solvent Dispenser

USD $25.30

Handy dispenser keeps chemicals such as mineral spirits, acetone, naptha, epoxy remover, and lacquer thinner from evaporating quickly and prevents dangerous spilling. A simple "tap" on the stopper/reservoir with a small towel, and the solvent pools to the top. Capacity 250 ml / 8.5oz